Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Sunset Park Homeowners
Most chimney problems in Sunset Park announce themselves in small ways: a bit of mortar on the roof after a cold snap, a stain on the ceiling after heavy rain, a draft that wasn’t there last winter. Those small signs are the reason to get someone on the roof and look, before a repointing job turns into a rebuild. Our technicians have up to 11 years of experience with masonry and liner work on the brick rowhouses and older walk-ups that make up so much of Sunset Park housing, and we diagnose the cause before we quote a repair.
Chimney repair means fixing the structure and the flue, not just cleaning them. A cracked crown, failed flashing, or crumbling mortar joint lets water into brick that was never meant to stay wet, and repair-grade work such as resurfacing with HeatShield or replacing a damaged liner with DuraFlex is part of what we handle. We can usually book a repair assessment the same day. Call (866) 937-8201 to set one up. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
What Our Chimney Repair Service Includes
Every repair starts with a real look at the chimney, not a guess. These are the specific masonry and liner repairs we take on, and each one addresses a different way a chimney fails.
Mortar Repointing
Repointing means cutting out the cracked, sandy mortar between bricks and packing fresh mortar into those joints. It’s the repair you need when the joints have eroded and the brickwork is starting to move but the bricks themselves are still sound. We match the mortar to the old masonry rather than slapping on a hard modern mix that can crack the brick around it as it cures. Whether the trouble is at the crown or down the length of the chase, this is the most common way we stop a chimney from getting worse.

Spalling Brick Repair
Spalling is when the face of a brick flakes off or crumbles, usually after repeated freeze-thaw cycles or water getting trapped behind a failed finish. Left alone, spalled brick lets moisture deeper into the wall and the damage spreads to the bricks beside it. We remove the failed units and replace them with brick that matches the rest of the chimney in size and color, then repoint the surrounding joints so the repair holds.

Chimney Waterproofing
Waterproofing applies a breathable sealer to the exterior brick so rain runs off instead of soaking in, while moisture already inside the chimney can still escape. You need it when the brick stays damp after rain, or when you’ve had repairs done and want to keep new mortar from failing the same way the old did. This is a preventive step we often recommend right after repointing or rebuilding, because a sealed chimney lasts far longer than an exposed one.

Flashing Repair
Flashing is the metal that seals the joint where the chimney passes through the roof, and it’s one of the most common sources of leaks people blame on the flue. When the flashing pulls away, rusts through, or was installed without proper step and counter-flashing, water runs down the chimney and into the ceiling below. We reset or replace the flashing and seal the seams so the roof-to-chimney junction is watertight, then confirm with photos that the fix is holding.
Chimney Rebuilding
A rebuild is in order when the top of the chimney has deteriorated past the point where repointing or patching will hold: loose bricks, a leaning stack, or a crown that has broken apart. We take the chimney down to solid masonry and rebuild it with new brick and mortar, matching the original profile as closely as possible. This is bigger work than a repoint, and we only recommend it when the camera and the roof inspection show it’s genuinely necessary rather than a convenient upcharge. If it can safely wait, we’ll tell you that too. For related fireplace work inside the house, see our Chimney Sweep Sunset Park service.
Tuckpointing
Tuckpointing is a finer version of repointing: we rake out the old mortar and fill the joint with a contrasting mortar to restore a crisp, finished look while sealing the joint. It’s often chosen for older chimneys where the masonry is visible from the street and the homeowner wants both repair and a clean appearance. The structural benefit is the same as repointing, and we make sure the mortar we use matches the original in strength so the brickwork stays protected.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Repair
We name the brands we install because the materials matter as much as the labor. DuraFlex is a flexible stainless liner system, and we know where it wears out: at the top plate, around any offset in the flue, and at the connections where heat and moisture do the most work. DuraFlex is what we reach for on a full flexible liner replacement, and we measure and fit it to the actual flue rather than a generic size. HeatShield is a resurfacing system for compromised flue liners, and it’s the repair-grade option that lets us restore a damaged clay liner that’s still structurally usable instead of tearing it out. Knowing how to apply HeatShield correctly is a diagnostic skill, not a cleaning one.
Olympia Chimney covers the components that keep a repaired chimney working: caps, liners, and the fittings that tie the system together. When we repair a chimney, we check that these parts are sound and replace the ones that aren’t, so a fresh masonry repair isn’t undermined by a failing cap or a loose liner connection. Whether you have DuraFlex, HeatShield, or Olympia Chimney equipment, or any other make, we can help, and we’ll tell you honestly which parts need replacing and which can stay.
Signs You Need Chimney Repair Right Now
These are the symptoms that mean it’s worth having the chimney looked at before the next storm, and none of them should be ignored.
- Crumbling mortar on the roof or at the base. If you’re finding grit and sand around the chimney, the joints are already failing. Left alone, water gets in and the brickwork starts to move.
- White staining or efflorescence on the brick. That chalky bloom is salt pushed out by moisture moving through the masonry. It usually points to water getting in somewhere, often a failed seal or flashing.
- Water stains on the ceiling or chimney breast. A stain after heavy rain is a flashing or crown problem until proven otherwise. Finding the source early saves a much larger interior repair later.
- Loose or missing bricks near the top. The crown and upper courses take the worst of the weather, and a loose brick is a sign the whole top section may need attention. Don’t wait for it to fall.
- A cracked or broken crown. The crown sheds water away from the flue, and once it cracks, rain runs straight down the chimney. It’s a small repair now and a bigger one if it’s ignored.
Our Chimney Repair Process – Step by Step
- 1
Book the visit. We schedule a time that works for you and confirm what we’ll look at. A repair assessment is a real inspection, not a quick glance from the ground.
- 2
Inspect the full system. We check the crown, brickwork, flashing, cap, and flue, and we use a camera to see the inside of the liner where the eye can’t reach. This is how we find the actual cause of a leak or draft, not just the most obvious symptom.
- 3
Show you the findings. We walk you through the camera footage and photos and explain what’s failing and why, in plain terms. You see the same evidence we do before any work is agreed.
- 4
Give you a written estimate. The estimate lists the specific repairs and the price for each, so you know exactly what’s being done and what it costs. Nothing is added after the fact, and if part of the job can safely wait, we say so.
- 5
Do the repair and verify it. We complete the masonry and liner work, then check it holds, with photos of the finished repair for your records. For repair-grade liner work we use products like HeatShield, and for full replacements we install DuraFlex. To get a baseline on the flue first, a full chimney repair assessment covers the whole system.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in Sunset Park?
Chimney repair in Sunset Park typically runs from a few hundred dollars for a targeted flashing or mortar repair up to several thousand for a full rebuild. A typical repointing job on a rowhouse chimney runs $600 – $1,800 depending on how much of the stack needs the joints cut out and refilled. Spalling brick repair is usually $400 – $1,200 depending on how many units are replaced. Chimney waterproofing runs $300 – $700 for the exterior sealer. Flashing repair is commonly $350 – $900, and a full chimney rebuild can run $3,000 – $8,000 or more, depending on height, access, and how far the deterioration goes. These are estimates for planning, and the written estimate sets the final price.
What moves the price is access to the roof, the height and condition of the stack, whether the repair is localized or the whole chase is failing, and whether the liner needs work at the same time. To avoid overpaying, get the findings in writing with photos and ask what can safely be postponed. We include both in every estimate, and the estimate itself is free. We diagnose before we quote, so there are no surprise add-ons once the work is agreed.
Chimney Repair Near Sunset Park – Our Service Area
We take on chimney repair across Sunset Park and the surrounding neighborhoods, including chimney repair in Borough Park, Kensington, Bay Ridge, Dyker Heights, and Carroll Gardens. Appointments in these areas are typically scheduled within the same working week, and we can often reach a same-day assessment. Call (866) 937-8201 and we’ll confirm the timing for your address. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. For nearby coverage, see our chimney repair page.
Serving Sunset Park, NY – Our Local Coverage Area
We serve Sunset Park and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Repair in Sunset Park
Chimney repair is fixing the structure and the flue, not just cleaning them. That covers masonry work such as repointing, spalling brick replacement, tuckpointing, rebuilding, plus the crown, flashing, waterproofing, and liner repair. It’s what you call when the chimney is damaged or leaking, not just dirty.
Most repairs take a day or less. A flashing repair or a small repoint is often finished in a single visit, while a larger repointing job or a full rebuild can span several days depending on weather and how much masonry needs to come out. We’ll give you a realistic timeline with the written estimate.
Most repairs fall between $300 and $8,000, with the exact figure depending on the repair type and how far the damage goes. Repointing, waterproofing, and flashing work are at the lower end, while a full rebuild is at the upper end. The written estimate sets the final price, and the estimate is free. Call (866) 937-8201 for an exact quote.
Yes. We install and repair DuraFlex flexible liner systems and apply HeatShield for flue resurfacing. We’ll assess whether your existing liner can be resurfaced or needs a full replacement, and we’ll show you the camera evidence so you can see why. Whether you have DuraFlex, HeatShield, or Olympia Chimney parts, we can help.
Yes, same-day repair assessments are often available. We dispatch Sunday through Friday, 7am to 7pm, and we’re closed Saturday. Call (866) 937-8201. We answer 24/7, and a call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
Yes, our repair work carries a satisfaction guarantee. If a repair we performed isn’t holding as it should, we’ll come back and make it right. We’ll explain the specific warranty terms for your repair in the written estimate. Call (866) 937-8201 with any questions.
Clear access to the chimney inside the house and to the roof where possible, and secure any pets. If you have a fireplace, don’t light it before the visit. Let us know if there are any known leaks or drafts. We’ll handle the rest and walk you through findings before any work starts.
Schedule Your Chimney Repair Service in Sunset Park Today
Don’t wait for a small mortar repair to become a rebuild. Call (866) 937-8201 to schedule a free chimney repair estimate in Sunset Park. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. We’ll inspect the full system, show you the camera findings, and give you a written quote before any work begins. No obligation, and no pressure.
Written by the team at Chimney Sweep Sunset Park.